28 MHz Rail-to-Rail Input/Output

Constant Gain from 2.7V to 5.5V Supply or ±1.35V to ±2.75V

Operates at Junction Temperatures from -40°C to +125°C

60dB@0.1～2GHz/50dB@2GHz～4GHz

/45dB@4GHz～6GHz

1.Four-channel 250MSPS ADC

2.Low power consumption, no heatsink required

3.Built-in Duty Cycle Stabilizer (DCS) for ADC clock

4.Internal reference voltage source integrated in ADC

5.Single 1.8V power supply operation supported

6.Programmable analog input range

7.LVDS outputs with programmable swing

8.Peak input voltage range: 1.4Vpp to 2.0Vpp (Typical: 1.75Vpp)

9.SPI control interface (4-wire) compatible with 1.8V or 3.3V logic

10.Flexible power-down modes for energy saving

1.±500°/s range

2. Compatible with SPl interface

3.-3dB Bandwidth (MHz):150Hz

4. Configurable output control

5. Adjustable output filter

6. Integrated temperature sensor

(1) Communication network peak Data Transfer Rate: 100 Mbps

(2) Message transmission delay complies with ARINC664 standard

(3) Meets the data frame forwarding requirements of ARINC664 Part 7 “Avionics Full Duplex Switched Ethernet” specification

(4) Supports dual AFDX network end system physical network selection

(1) Provides functional interface compliant with IEEE1394B-2002 standard

(2) Single-node 1394B bus interface with three external Beta I/O Ports

(3) Supports S100B, S200B, and S400B Data Transfer Rates

(4) Provides standard PCIe 2.0 host interface (1 Lane)

(5) Supports SAE AS5643/02 application protocol

(6) CC/RN mode configuration capability

(7) Supports bus configuration table storage

(8) Provides built-in BIT (Built-In Test) functionality

(9) Weight not exceeding 50g, power consumption not exceeding 5W

(1) Implements 1 dual-redundant MIL-STD-1553B bus interface

(2) Supports BC (Bus Controller) / RT (Remote Terminal) functionality

(3) Bus speed is 4 Mbps, configurable to be compatible with 1 Mbps

(4) Response time ≤ 3 µs

(5) Uses transformer coupling

(6) Power supply input: 5V ±5%, power consumption ≤ 3W

(1) Complies with ARINC664 Part 7, supports UDP/IP protocol

(2) Provides dual-redundant full-duplex Ethernet physical layer interfaces, meeting 100 Mbps Ethernet specifications

(3) Message transmission delay meets ARINC664 standard

(4) Supports transmission and reception of 128 VLs each, with VL BAG configurable up to 2 KMS (K is an integer from 0 to 7)

(5) Supports BIT (power-on BIT, periodic BIT, maintenance BIT)

(6) Transmit/receive technical delay less than 200 µs

(7) Uses PMC architecture, PCI bus clock at 33 MHz, 32-bit data bus

(1) Complies with FC-FS-2 and FC-PI-4 protocol requirements, adopts FC-2 layer switching, supports FC-3 class services, and supports ELS frame transmission and reception

(2) I/O Ports rate: 2.125 Gbps

(3) Supports 48 optical signal transmission interfaces, with data transmission bit error rate ≤ 10⁻¹²

(1) Complies with FC-PI and FC-FS protocol requirements

(2) Provides 1 high-speed serial data input interface and 1 FC communication interface

(3) FC interface communication rate: 2.125 Gbps, full-duplex communication with bit error rate ≤ 10⁻¹²

1. Main chip: Xilinx FPGA XC7VX690T-FFG1761

2. Onboard EEPROM for storing parameter configurations and other information

3. Standard PCle interface, supports PCle x8 and PCle 3.0 protocol

4. Supports 2 sets of 64-bit DDR3 memory, each with 4 GB capacity

5. BPl Flash 128 MB for program loading

6. Supports 1 FMCHPC

7. Panel features 1 SFP+ optical channel with a maximum design speed of 10Gbps

8. Also supports an additional 2 SFP+ optical channels

9. Supports 4 LED indicators

10. All components support commercial and industrial grade standards